Next  |  Prev  |  Up  |  Top  |  Index  |  JOS Index  |  JOS Pubs  |  JOS Home  |  Search


First-Order Allpass Interpolation

A delay line interpolated by a first-order allpass filter is drawn in Fig.4.3.

Figure 4.3: Allpass-interpolated delay line.
\includegraphics[width=\twidth]{eps/delayai}

Intuitively, ramping the coefficients of the allpass gradually ``grows'' or ``hides'' one sample of delay. This tells us how to handle resets when crossing sample boundaries.

The difference equation is

\begin{eqnarray*}
{\hat x}(n-\Delta) \isdef y(n) &=& \eta \cdot x(n) + x(n-1) - \eta \cdot y(n-1) \\
&=& \eta \cdot \left[ x(n) - y(n-1)\right] + x(n-1).
\end{eqnarray*}

Thus, like linear interpolation, first-order allpass interpolation requires only one multiply and two adds per sample of output.

The transfer function is

$\displaystyle H(z) = \frac{\eta + z^{-1}}{1 + \eta z^{-1}}. \protect$ (5.2)

At low frequencies ($ z\to 1$ ), the delay becomes

$\displaystyle \Delta \approx \frac{1-\eta}{1+\eta} \protect$ (5.3)

Figure 4.4 shows the phase delay of the first-order digital allpass filter for a variety of desired delays at dc. Since the amplitude response of any allpass is 1 at all frequencies, there is no need to plot it.

Figure 4.4: Allpass-interpolation phase delay for a variety of desired delays (exact at dc).
\includegraphics[width=\twidth]{eps/allpass1}

The first-order allpass interpolator is generally controlled by setting its dc delay to the desired delay. Thus, for a given desired delay $ \Delta$ , the allpass coefficient is (from Eq.(4.3))

$\displaystyle \eta \approx \frac{1-\Delta}{1+\Delta}
$

From Eq.(4.2), we see that the allpass filter's pole is at $ z=-\eta$ , and its zero is at $ z=-1/\eta$ . A pole-zero diagram for $ \Delta =0.1$ is given in Fig.4.5. Thus, zero delay is provided by means of a pole-zero cancellation! Due to inevitable round-off errors, pole-zero cancellations are to be avoided in practice. For this reason and others (discussed below), allpass interpolation is best used to provide a delay range lying wholly above zero, e.g.,

$\displaystyle \Delta\in[0.1,1.1] \;\longleftrightarrow\; \eta\in[-0.05,0.82]
$

Figure 4.5: Allpass-interpolator pole-zero diagram for $ \Delta =0.1$ .
\includegraphics[width=\twidth]{eps/ap1pz}
Note that, unlike linear interpolation, allpass interpolation is not suitable for ``random access'' interpolation in which interpolated values may be requested at any arbitrary time in isolation. This is because the allpass is recursive so that it must run for enough samples to reach steady state. However, when the impulse response is reasonably short, as it is for delays near one sample, it can in fact be used in ``random access mode'' by giving it enough samples with which to work.

The STK class implementing allpass-interpolated delay is DelayA.



Subsections
Next  |  Prev  |  Up  |  Top  |  Index  |  JOS Index  |  JOS Pubs  |  JOS Home  |  Search

[How to cite this work]  [Order a printed hardcopy]  [Comment on this page via email]

``Physical Audio Signal Processing'', by Julius O. Smith III, W3K Publishing, 2010, ISBN 978-0-9745607-2-4
Copyright © 2024-06-28 by Julius O. Smith III
Center for Computer Research in Music and Acoustics (CCRMA),   Stanford University
CCRMA