Jeff Rowell 250B

From CCRMA Wiki
Jump to: navigation, search

Jeffrey Rowell-Reverberant Art

"Keeping Time"- Pendulum Guitar

An exploration of changing timbres, Keeping Time uses pickups set on pendulums to bring into relief the link between musical tempo and life tempo.

A set of coupled pendulums with mounted electromagnetic pickups are set in front of a semi-hollow electric guitar. The guitar has a mounted transducer attached to the soundboard on the back of the guitar and is playing several simultaneous frequency sweeps to induce vibrations in the strings, which are then detected in the pickups and played through a small amplifier on the ground below the installation.


1)Guitar- A red Ibanez Artcore AS73 has been selected. The transducer mounts directly behind the bridge, and is held in place with double sided padded tape. As the placement falls directly between the strap hooks, string is used to provide additional reinforcement. The amplifier driving the transducer is fed a signal by a small mp3 player; multiple overlapping sine wave frequency sweeps of varying velocity are used to excite the strings

Jrowell overall.JPG Jrowell transducer.JPG

2)Pendulums- Two linked pendulums are mounted over the strings. They are placed so that their neutral position is over the high and low strings to allow each pickup segments of time detecting various strings and detecting silence. The distance between the pendulums is approximately two and a half inches so to allow free motion the bottom of one of the pendulum features an offset split structure that allows the pendulums to freely swing through each other. The pendulums are suspended by knife edge mounts, and project through an aluminum plate. The plate has grooves cut to allow placement of the pendulum mounts and to avoid slipping or walking as the pendulums swing.

Jrowell pendulum.JPG Jrowell pendulums.JPG

Jrowell pendulum3.jpg Jrowell pendulum2.JPG

3)Pickups- Strat pickups are used. One is mounted above the pivot point of the pendulum and one below to catch different harmonic resonances on the strings. The distance between them is such that one will be mounted at approximately the 12th fret of the guitar and one above the 24th, placing them above the nodes of the first and second overtones of the strings.

The relative volume of the tones generated by the transducer is low and a relatively high gain on the amplifier must be used. Unfortunately that means that if a spectator strums the strings or the pendulums are moved from their tracks in such a way as to contact the strings excessive volume would be produced and so a compressor/limiter pedal is used in the signal chain.

4)Mounting- The installation will be wall mounted, with the mounting supporting the pendulums and guitar, and the amplifier set below on the floor.

5)Presentation- Ideally, the body of the guitar will be mounted around 4.5 feet off the ground, where the pendulums are easily touched but the headstock is uncomfortably high to reach. It should be lit with a spot from above to highlight the changing shadows as the pendulums move.

Preliminary Project Ideas

1)Selectable Spring Reverb

Two soundboards with high tension springs between them with a controllable damper on each spring. One sound is input on one side and picked up on the other with variable amounts of reverb. The control system would be a set of foot pedals/switches similar to organ foot pedals which would raise dampers off springs to allow them to transmit sound.


2)Variable Reverb Room

A room with a microphone and moveable walls/ceiling which would analyze the pitch of voices within it and attempt to change the shape of the room to highlight harmonics in the voice.


3)Morse code through Spring Reverb

Sending Morse Code through reverb and then attempting decoding, explore the chaotic mistranslations that would occur given significant signal distortion.


4)Coupled Pendulum Pickups

A pair of guitar pickups are mounted on a set of coupled pendulums, and then set in front of two strings vibrating at close but different frequencies. The output of the pickups is then fed into a loudspeaker mounted close behind the system for feedback.


This is my favorite concept currently due to the combination of simple concepts and extremely complicated output.

5)Clocking output through variable pendulum.

A spring pendulum, such that the movement of the spring changes the center of mass of the pendulum and modulates the period. This would create a system linking the visual distortion of time and the audio distortion of time.

6)Distortion of Visual projection by Reverb

7) Wire over Ferrofluid

A wire suspended over ferrofluid, with a current applied based on the output of a set of speakers. The gain on the sound sources is then controlled by the tension on the wire, such that the increase in ferrofluid weight on the wire lowers the gain. This would create a reactive loop of (increase in fluid weight)->(lowering of gain)->(lowering of wire current)->(decrease in fluid weight on wire). Depending on the latency of the system, convergent, divergent or stable systems could be created.

8) Ferrofluid reverberation tracker (most idea credit to Eoin)

Ferrofluid held on a small powerful magnet forms a nice spiky mushroom shape, which is responsive to both motion and wind pressure. A few of these mounted in the ports of subwoofers would create a cool visualization of sounds run through the woofer, as well as pressure changes in the room caused by motion and door openings.