Satellite CCRMA Windows 10

Connect

This page explains how to connect to Satellite CCRMA from a Windows 10 machine.

Windows 10

• First power up Satellite CCRMA, use an ethernet cable to connect Satellite CCRMA to your Windows machine, and make sure that the light on the ethernet interface on the windows machine turns on. (If the light does not turn on, then you will not be able to find the ethernet interface in the control panel to change its settings.)

• Go to the Control Panel app
• Click on Network and Internet
• Click on Connect to a Network
• Then click on Network & Internet Settings
• Find your Ethernet interface listed on the left and click on it
• Click on Change Adapter Options
• Then double-click on the Ethernet device
• Next, click on Properties. You should see something like the following:

• Find the Internet Protocol Version 4 (TCP/IPv4), enable it if necessary, and double-click on it.

• Close out of all those windows.

• Download PuTTY from https://www.putty.org/

You probably want the 64-bit x86 option.

• Install PuTTY

• Download VcXsrv from https://sourceforge.net/projects/vcxsrv/ and install it as well.
• Start XLaunch, which will be in the VcXsrv folder in the Windows start menu.
• Choose the first option as shown below

• Press Next
• Then for the new dialog, choose Start no client and press Next.
• As shown in the following dialog, make sure that Disable access control is checked:

• Then click Next and then Finish.

• Start the PuTTY app.
• Open up Connection | SSH | X11
• Enable X11 forwarding as shown below:

• Then go back up to Session and enter the host name ccrma@192.168.105.106 as follows:

• Type in a name for the saved session something like e.g. RPiX11 and Save it for next time.
• Click on Open.
• Use the password temppwd
• After you login in, stop the default audio program from running by typing

stop-default

• Then start pd with the following command and have at it!

pd &

• Go to Control Panel\Network and Internet\Network Connections (or Control Panel\Network and Internet\Network and Sharing Center), right-click on Local Area Network (or Local Area Connection) and go to Properties. Select Internet Protocol Version 4 (TCP/IPv4), and click on Properties. There, manually configure:
  IP Address: 192.168.105.105
  Subnet Mask: 255.255.255.0
  Standard gateway: 192.168.105.1
  Leave the remaining items as they are. The following image is from Windows 7 installed in German and might help you navigate through these settings:

• Start the Xming program from the Start Menu--it is in a folder called Xming. If you don't already have it, then download XMING, install it, and start it.

• If you haven't already, then download Putty. It will stay in your Downloads folder unless you put it somewhere else, such as the Desktop.
  • Go to the Connection | SSH | X11 panel and check "Enable X11 forwarding"
    
  • Go to the Connection | SSH | Tunnels panel and check "Local ports accept connections from other hosts"
    
  • Go to the Session panel and enter ccrma@192.168.105.106 into the "Host name" field to specify that you want to log in to 192.168.105.106 (the IP address of Satellite CCRMA) using the user name ccrma.
    
  • Select "Default Settings" and then click the "Save" button so that all these settings are saved by default.
  • Finally click on the "Open" button to open the connection.
  • The password is temppwd
  • Since a default pd patch started on boot, you can stop it by typing stop-default
  • Then run the command
    pd &
    to make sure that pd can successfully forward its Window to your laptop.

Windows Troubleshooting

• If when you run pd &, pd is unable to forward a window to your laptop, then you should first run pkill pd to quit pd. Then, make sure that you followed all of the steps above. If that still doesn't work, then try running the following command remotely on Satellite CCRMA before running pd &:
  export DISPLAY=192.168.105.105:0
• If you are still having difficulty, please ask the teaching staff for help.
• Maybe also try looking at this link.
• If this is the second time you are trying connecting to your kit, make sure that you are running Xming.

Experts Only: Alternate Approach

• If you are an expert and you prefer to use cygwin instead (which can take hours to install!), then follow these instructions:
  • X Windows is included in the current Cygwin/X distribution. (Cygwin/X installer can be downloaded from [1].) Choose only the required packages from Cygwin are openssh and xinit.